工艺参量对同轴送粉喷嘴气体保护效果的影响

易德先; 胡芳友; 徐成伟; 崔爱永; 卢长亮

doi:10.3969/j.issn.1001-3806.2010.O5.003

工艺参量对同轴送粉喷嘴气体保护效果的影响

1.
海军航空工程学院青岛分院, 航空机械系, 青岛, 266041

作者简介: 易德先(1974- ),男,博士研究生,工程师,现主要从事激光加工技术在航空飞行器维修领域中的应用研究..

通讯作者: 胡芳友, fyh1960@sing.com ;

中图分类号: TN249

Effect of process parameters on gas shield of coaxial powder feeder nozzles

1.
Department of Mechanical Mechanism, Qingdao Branch of Naval Aeronautical Engineering Institute, Qingdao 266041, China

Corresponding author: HU Fang-you, fyh1960@sing.com ;

CLC number: TN249

摘要: 为了解决激光直接制造金属零件中同轴送粉喷嘴气体保护效果不佳的问题,采用烟雾流动显示技术对喷嘴保护气体流场进行了研究。系统研究了喷嘴保护气流速率、喷嘴出口距零件表面距离、喷嘴移动速率和侧风速率对气体保护效果的影响。结果表明,随着喷嘴保护气流速率的增加,保护范围先增加后减小;随着侧风速率和喷嘴移动速率的增大,气流轴线偏离喷嘴轴线距离增大;当侧风速率超过喷嘴气流速率50%,距喷嘴出口10mm处,气流完全偏离喷嘴轴线,完全失去对金属熔池的保护。这一结果为选择合适的喷嘴气流参量提供了依据。
- 激光技术 /
- 工艺参量 /
- 烟雾流动显示 /
- 同轴送粉喷嘴
Abstract: In order to improve the shielding effect of gas flow field in laser direct manufacturing, the shielding gas flow field of coaxial powder feeder nozzles was studied by means of smoke flow visualization technology.The influence of gas velocity from nozzle, distance between parts and nozzle exit,moving velocity of nozzle and crosswind velocity on shielding gas field was investigated systematically. The results show that with the increase of gas velocity from nozzle,shielding effect increases at first and then gets worse; with the increase of velocity of crosswind and nozzle,the axis of shielding field and nozzle get apart; when the velocity of crosswind surpasses 50% of velocity of gas from nozzle, shielding field fails to protect molten pool totally at the place 10mm below the nozzle.The information can be used to select appropriate nozzle flow parameters.
- laser technique /
- process parameter /
- smoke flow visualization /
- coaxial powder feeder nozzle

[1]	ZHANG H J,ZHONG M L,LIU W J,et al.Develop of high convergent coaxial feeding nozzle with temperature display for laser rapid manufacturing[J].Applied Laser,2004,24(6):380-382(in Chinese).
[2]	ZHONG M L,NING G Q,LIU W J.Research and development on laser direct manufacturing metallic components[J].Laser Technology,2002,26(5):388-391(in Chinese).
[3]	LIN J,STEEN W M.Powder flow and catchment during coaxial laser cladding[J].Proc SPIE,1997,3097:517-528.
[4]	ANCONA A,TERESA S,PIETRO M L,et al.An analysis of the shielding gas flow from a coaxial conical nozzle during high power CO2 laser welding[J].J Phys,2006,D39(3):563-574.
[5]	JIN X Sh,YANG X Ch,WANG Y Sh,et al.Research on the coaxial powder feeder nozzle in 3-D direct manufacturing and re-manufacturing[J].Applied Laser,2008,28(4):266-270(in Chinese).
[6]	ZHANG L J,ZHANG J X,WANG R,et al.Effects of side assist gas on the CO2 laser welding process of thin stainless plate[J].Applied Laser,2005,25(4):217-221(in Chinese).
[7]	LI L.Modelling powder concentration distribution from a coaxial deposition nozzle for laser-based rapid tooling[J].Journal of Manufacturing Science and Engineering,2004,126(1):33-41.
[8]	LIN J.Numerical simulation of the focused powder streams in coaxial laser cladding[J].Journal of Materials Processing Technology,2000,105(1/2):17-23.
[9]	LI H Sh,WANG Ch X,FU J Ch,et al.Research on the coaxial carrier-gas powder feed laser cladding[J].Applied Laser,2006,26(4):223-226(in Chinese).
[10]	YANG N,YANG X Ch.Numerical simulation of flow field of nozzle in laser cladding[J].Chinese Journal of Lasers,2008,35(3):452-455(in Chinese).
[11]	YANG X Ch.Momentum and mass transferences of coaxial powder stream in laser manufacturing[J].Chinese Journal of Lasers,2008,35(11):1664-1679(in Chinese).
[12]	YANG X Ch,LEI J B,LIU Y W,et al.Experimental measurement of metal powder stream concentration field in laser manufacturing[J].Chinese Journal of Lasers,2006,33(7):993-997(in Chinese).
[13]	GU Y S,MING X.Investigation on the characteristics and structures of unsteady flow field near the zero-mass flux jet with PIV[J].Journal of Experiments in Fluid Mechanics,2005,19(1):83-86(in Chinese).
[14]	HUANG R,HU Zh H,CHEN K.The study of laser welding shielded gas by schlieren[J].Welding Technology,2007,36(2):8-11(in Chinese).

[1]	周聪 , 夏海龙 , 陈根余 , 李时春 , 黎长邹 . 光纤激光焊接工艺参量对底部驼峰的影响. 激光技术, 2015, 39(5): 625-630. doi: 10.7510/jgjs.issn.1001-3806.2015.05.009
[2]	龚丞 , 王丽芳 , 朱刚贤 , 宋天麟 . 激光增材制造工艺参量对熔覆层残余应力的影响. 激光技术, 2019, 43(2): 263-268. doi: 10.7510/jgjs.issn.1001-3806.2019.02.021
[3]	储晓猛 , 顾佩兰 , 杨建新 . 高密度聚乙烯塑料激光焊接工艺参量试验研究. 激光技术, 2010, 34(1): 116-119. doi: 10.3969/j.issn.1001-3806.2010.01.033
[4]	白少俊 , 常保华 , 张骅 , 都东 . 工艺参量对NdFeB永磁体和SPCC钢激光点焊质量的影响. 激光技术, 2010, 34(2): 149-153. doi: 10.3969/j.issn.1001-3806.2010.02.002
[5]	黄海博 , 孙文磊 . Ni60激光熔覆工艺参量对涂层裂纹及厚度的影响. 激光技术, 2021, 45(6): 788-793. doi: 10.7510/jgjs.issn.1001-3806.2021.06.019
[6]	孟伟栋 , 石世宏 , 傅戈雁 , 王涛 , 杨轼 , 史建军 . 光内同轴送粉立面堆积成形实验研究. 激光技术, 2015, 39(5): 594-597. doi: 10.7510/jgjs.issn.1001-3806.2015.05.003
[7]	李忠 , 王涛 , 刘佳 , 石岩 , 白陈明 , 栗红星 . 工艺参量对铝合金复合焊接接头耐蚀性的影响. 激光技术, 2019, 43(2): 189-194. doi: 10.7510/jgjs.issn.1001-3806.2019.02.008
[8]	赵士伟 , 张海云 , 李志永 , 赵玉刚 , 张晋烨 . 激光参量对血管支架切缝形貌及粗糙度的影响. 激光技术, 2020, 44(3): 299-303. doi: 10.7510/jgjs.issn.1001-3806.2020.03.005
[9]	陈菊芳 , 陈国炎 , 孙凌燕 , 王江涛 , 李兴成 . H13钢表面激光熔覆层稀释率及强化效果研究. 激光技术, 2017, 41(4): 596-601. doi: 10.7510/jgjs.issn.1001-3806.2017.04.028
[10]	陈根余 , 陈明 , 李时春 , 谭立鹏 . 非熔透激光搭接焊薄钢板的试验研究. 激光技术, 2011, 35(5): 577-581. doi: 10.3969/j.issn.1001-3806.2011.05.001
[11]	高亚丽 , 王存山 , 张梅 , 熊党生 . 镁合金激光表面熔凝技术分析. 激光技术, 2009, 33(4): 362-365. doi: 10.3969/j.issn.1001-3806.2009.04.008
[12]	张奇 , 沈磊 , 何博 . 飞秒激光在金属微加工中的应用. 激光技术, 2021, 45(4): 429-435. doi: 10.7510/jgjs.issn.1001-3806.2021.04.004
[13]	张晓刚 , 李宗义 , 刘艳 , 张昊 . 激光选区熔化纯铜成形件尺寸精度的研究. 激光技术, 2017, 41(6): 852-857. doi: 10.7510/jgjs.issn.1001-3806.2017.06.017
[14]	顾江 , 叶霞 , 范振敏 , 张鹏 , 刘群超 , 徐伟 . 激光刻蚀法制备仿生超疏水表面的研究进展. 激光技术, 2019, 43(4): 493-499. doi: 10.7510/jgjs.issn.1001-3806.2019.04.011
[15]	周辽 , 龙芋宏 , 焦辉 , 覃婷 , 黄宇星 , 张光辉 , 黄平 , 钟志贤 . 激光加工碳纤维增强复合材料研究进展. 激光技术, 2022, 46(1): 110-119. doi: 10.7510/jgjs.issn.1001-3806.2022.01.011
[16]	郭翔宇 , 倪茂 , 刘华明 , 雷凯云 , 杜甫 . 宽带激光熔覆同轴送粉喷嘴的设计与数值模拟. 激光技术, 2018, 42(3): 362-368. doi: 10.7510/jgjs.issn.1001-3806.2018.03.014
[17]	雷定中 , 石世宏 , 傅戈雁 . 激光宽带熔覆光内送粉喷嘴准直气罩研制. 激光技术, 2015, 39(5): 590-593. doi: 10.7510/jgjs.issn.1001-3806.2015.05.002
[18]	周余 , 杨永强 , 黄延禄 . 激光熔覆孔式同轴送粉系统设计及实验研究. 激光技术, 2011, 35(1): 102-105. doi: 10.3969/j.issn.1001-3806.2011.01.028
[19]	徐磊 , 刘西霞 , 李庆福 , 胡光蓉 , 张屹 . 高强镀锌钢激光填粉焊接工艺试验研究. 激光技术, 2014, 38(1): 1-5. doi: 10.7510/jgjs.issn.1001-3806.2014.01.001
[20]	陈寰宇 , 吴家柱 , 赵鹏辉 , 刘安丽 , 张屹 . 激光直接金属沉积316L不锈钢表面粘粉工艺研究. 激光技术, 2019, 43(5): 624-628. doi: 10.7510/jgjs.issn.1001-3806.2019.05.007

点击查看大图

计量

文章访问数: 4241
HTML全文浏览量: 620
PDF下载量: 239
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

工艺参量对同轴送粉喷嘴气体保护效果的影响

作者简介: 易德先(1974- ),男,博士研究生,工程师,现主要从事激光加工技术在航空飞行器维修领域中的应用研究..

通讯作者: 胡芳友, fyh1960@sing.com ;

Effect of process parameters on gas shield of coaxial powder feeder nozzles

Corresponding author: HU Fang-you, fyh1960@sing.com ;

计量

工艺参量对同轴送粉喷嘴气体保护效果的影响

通讯作者: 胡芳友, fyh1960@sing.com;

作者简介: 易德先(1974- ),男,博士研究生,工程师,现主要从事激光加工技术在航空飞行器维修领域中的应用研究.

English Abstract

Effect of process parameters on gas shield of coaxial powder feeder nozzles

Corresponding author: HU Fang-you, fyh1960@sing.com

全文HTML

目录

留言板

工艺参量对同轴送粉喷嘴气体保护效果的影响

作者简介: 易德先(1974- ),男,博士研究生,工程师,现主要从事激光加工技术在航空飞行器维修领域中的应用研究..

通讯作者: 胡芳友, fyh1960@sing.com ;

Effect of process parameters on gas shield of coaxial powder feeder nozzles

Corresponding author: HU Fang-you, fyh1960@sing.com ;

计量

出版历程

工艺参量对同轴送粉喷嘴气体保护效果的影响

通讯作者: 胡芳友, fyh1960@sing.com;

作者简介: 易德先(1974- ),男,博士研究生,工程师,现主要从事激光加工技术在航空飞行器维修领域中的应用研究.

English Abstract

Effect of process parameters on gas shield of coaxial powder feeder nozzles

Corresponding author: HU Fang-you, fyh1960@sing.com

全文HTML

目录