基于热裂法的液晶玻璃基板激光切割技术研究

汪旭煌; 姚建华; 周国斌; 楼程华; 杨渊思

doi:10.3969/j.issn.1001-3806.2011.04.009

基于热裂法的液晶玻璃基板激光切割技术研究

1.
浙江工业大学特种装备制造与先进加工技术教育部/浙江省重点实验室, 杭州 310014;
2.
浙江工业大学激光加工技术工程研究中心, 杭州 310014;
3.
浙江工业大学理学院, 杭州 310014

作者简介: 汪旭煌(1985- ),男,硕士研究生,主要从事激光与物质相互作用方面的研究..

通讯作者: 汪旭煌, laser@zjut.edu.cn ;

基金项目:
浙江省科技厅资助项目(2009C31104)
中图分类号: TG485

Research of the technology of laser cutting LCD glass substrates based on thermal cracking method

WANG Xu-huang^1,2,3, ,,

1.
Key Laboratory of Equipment and Advanced Manufacturing Technology, Ministry of Education & Zhejiang Province, Zhejiang University of Technology, Hangzhou 310014, China;
2.
Research Center of Laser Processing Technology and Engineering, Zhe-jiang University of Technology, Hangzhou 310014, China;
3.
College of Science, Zhejiang University of Technology, Hangzhou 310014, China

Corresponding author: WANG Xu-huang, laser@zjut.edu.cn ;

CLC number: TG485

摘要: 为了实现液晶玻璃基板的可控断裂切割,提出了一种液晶玻璃基板激光切割的新方法。采用Nd:YAG激光在液晶玻璃基板上预置初始裂纹,用CO2激光作为热源对其进行加热,并用Ar气进行冷却。分析了激光光斑尺寸和液晶玻璃基板厚度对切割的影响,并与传统机械切割进行了对比。用扫描电子显微镜检测了激光切割后切割表面及断面形貌。结果表明,运用机械切割,其基体内存在大量的微裂纹,而基于热裂法的液晶玻璃基板激光切割表面光滑平直、无毛刺、基体内无微裂纹存在,切割断面影响区小于20μm,优越性明显高于机械切割。
- 激光技术 /
- 激光切割 /
- 裂纹控制法 /
- 液晶玻璃基板 /
- 裂纹扩展
Abstract: In order to cut liquid crystal display (LCD) glass substrates with controlled crack,a new method was put forward.Firstly,an initial crack was prepared on the surface of LCD substrates with Nd: YAG laser.Then,the substrate was heated up with CO2 laser and cooled with Ar gas.The effect of laser spot size and the thickness of LCD glass substrates on laser cutting quality was analyzed.The surface and performance of the cutting face after laser treatment was tested by means of scanning electronic microscope (SEM).The cutting quality was compared with the traditional mechanical cutting quality.The results show that there are lots of micro cracks in the substrates cut with traditional mechanical method,however,the laser cutting surface based on thermal cracking method is smooth and flat,no micro cracks exists,and the cutting section-affecting zone is less than 20μm.It is better to cut LCD glass substrates with thermal crack laser cutting method than mechanical cutting method.

[1]	JIAO J K,WANC X B,LI Y P.Research progress on glass cutting by laser[J].Glass,2007,34(4):8-12(in Chinese)
[2]	LI Ch.The present statua and development trend of glass for TFTLCD application[J].Class,2006,33(1):15-23(in Chinese)
[3]	FU G Zh.Laser cutting technology glass[J].OME Information,2008,13(7):5-11(in Chinese).
[4]	ZHOU Sh F,ZENG X Y.Laser aeparation of brittle material[J].Journal of Applied Optics,2007,28(3):321-325(in Chinese).
[5]	LUMLEY R M.Controlled aeparation of brittle materials using a laser[J].American Ceramic Society Bulletion,1969,48(1):850-854.
[6]	GROVE R,DAE H C,SU W,et al.Laser cutting apparatus and method:US 3543979[P].1970-1001.
[7]	TSAI C H,LIOU C S.Fracture mechanism oflaser cutting with controlled fracture[J].Journal of Manufacturing Science and Engineering,2003,125(8):519-528.
[8]	TSAI C H,UN B C.Laser cutting with controlled fracture and prebending applied to LCD glass separation[J].Intemational Journal of Advanced Manufactaring Technology,2007,32(3):1155-1162.
[9]	TSAI C H,HUANG B W.Diamond acribing and laser breaking for LCD glass subetrates[J].Journal of Materials Processing Technology,2008,198(1/3):350-358.
[10]	NISAR S,SHEIKH M A,LI L.Effect of thermal stresses on chipfree diode laaer cutting of glass[J].Optics & Laser Technology,2009,41(3):318-327.
[11]	ZHOU Y,LIU X Sh,CHEN X Y,et al.Modeling on the parameters of laser cutting quartz crystal[J].Laser Technology,2000,24(2):74-77(in Chinese).
[12]	YUAN M Q,UNG H Zh,PENG B.Precision laser cutting technique for thin quartz glass plates[J].Laser Technology,2006,30(4):406-408(in Chinese).
[13]	JIAO J K,WANG X B.Temperature distribution of moving quartz glass heated by CO2 laser[J].High Power Laser and Particle Beams,2007,19(1):14(in Chineae).
[14]	JIAO J K,WANG X B,LU H.Analysis of temperature field and thennal 8tress field in quartz glass heated by laser beams[J].Laser Technology,2007,31(4):427-430(in Chinese).
[15]	XU G L,LI Y X,HUANG S Y,et al.Numerical simulation of cutting glass with double-beam CO2 laser[J].Huazhong Uruversity of Science & Technology Nature Science,2007,35(1):88-90(in Chinese).
[16]	LI L J.Modern laser processing and equipment[M].Beijing:Higher Education Press,1993:120-129(in Chinese).
[17]	YIN S M,ZHANG L H,XU R J,er al.Experimental analyaia of glass cutting by laser thennal Stress[J].Engineering Science,2007,9(3):67-70(in Chinese).
[18]	BRIAN L.Fracture of brittle solids[M].Beijing:Higher Education Press,2010:32-40(in Chinese).
[19]	YE Sh L,HUANG X,MA J Sh,et al.A study of cutting LCD glass substrates by laser[J].Journal of Applied Optics,2006,26(6):401-404(in Chinese).
[20]	YANG X H,LUAN M T.Study of brittle/ductile fracture mechanism and criterion of crack tip deformation theory[D].Dalian:Dalian Univeraity of Technology,2005:12-14(in Chinese).

[1]	卢希文 , 王海林 , 朱晓 , 朱广志 . 6.45μm激光加热浮法玻璃后温度分布特性研究. 激光技术, 2019, 43(3): 369-373. doi: 10.7510/jgjs.issn.1001-3806.2019.03.015
[2]	贾信庭 , 贺昌玉 , 王又青 . 激光切割系统功率实时控制研究. 激光技术, 2009, 33(2): 145-146,150.
[3]	黄福民 , 谢小柱 , 魏昕 , 胡伟 , 苑学瑞 . 半导体晶圆激光切割新技术. 激光技术, 2012, 36(3): 293-297.
[4]	张永强 , 吴艳华 , 陈武柱 , 张旭东 . 激光切割光辐射与切割质量关系的研究. 激光技术, 2007, 31(4): 397-399,444.
[5]	谢小柱 , 李力钧 , 张屹 , 刘继常 , 鄢锉 . 激光切割金属厚板新技术. 激光技术, 2005, 29(3): 251-254.
[6]	侯红玲 , 彭玉海 , 解玉坤 , 彭凯 , 张晖 . 激光切割对飞机蒙皮疲劳性能的影响分析. 激光技术, 2016, 40(3): 417-421. doi: 10.7510/jgjs.issn.1001-3806.2016.03.025
[7]	贾志新 , 黄金刚 , 高坚强 , 房泽旭 , 张亚洲 , 崔子月 . 长脉宽激光切割聚晶立方氮化硼工艺研究. 激光技术, 2017, 41(3): 346-350. doi: 10.7510/jgjs.issn.1001-3806.2017.03.009
[8]	张冲 , 王冠 , 杨志刚 , 刘赞丰 . 脉冲光纤激光切割连杆裂解槽工艺参量优化. 激光技术, 2018, 42(3): 422-426. doi: 10.7510/jgjs.issn.1001-3806.2018.03.025
[9]	晏一菓 , 阳如坤 , 李建相 , 吴学科 , 张屹 . 激光切割锂电池负极极片复合材料的数值模拟. 激光技术, 2019, 43(6): 773-778. doi: 10.7510/jgjs.issn.1001-3806.2019.06.008
[10]	史晓强 . 低碳钢板的激光切割. 激光技术, 1998, 22(6): 343-345.
[11]	鄢锉 , 李力钧 , 李娟 , 谢小柱 , 张屹 . 激光切割板材表面质量研究综述. 激光技术, 2005, 29(3): 270-274.
[12]	齐立涛 , 刘凤聪 , 张耀东 . 266nm紫外固体激光切割碳纤维复合材料的实验研究. 激光技术, 2022, 46(3): 402-407. doi: 10.7510/jgjs.issn.1001-3806.2022.03.017
[13]	周岩 , 刘晓胜 , 陈向阳 , 杨乐民 . 石英晶体激光切割参数建模. 激光技术, 2000, 24(2): 74-78.
[14]	楼祺洪 , 章琳 , 叶震寰 , 董景星 , 魏运荣 . 紫外激光切割Si片的实验研究. 激光技术, 2002, 26(4): 250-251,254.
[15]	刘建华 , 陈一坚 , 段军 , 胡席远 . 激光切割超音速喷嘴设计. 激光技术, 2000, 24(1): 46-50.
[16]	黄文荣 , 徐宾 , 汤光平 , 杨家林 . 大角度斜面激光切割加工的工艺研究. 激光技术, 2001, 25(4): 290-292.
[17]	王春明 , 胡伦骥 , 胡席远 . 国外激光切割实时监测技术的最新进展. 激光技术, 2001, 25(6): 412-417.
[18]	唐代明 , 苟淑云 , 王军 . 低合金相变诱发塑性(TRIP)钢激光焊接的研究进展. 激光技术, 2012, 36(2): 145-150,178. doi: 10.3969/j.issn.1001-3806.2012.02.001
[19]	杨永强 , 李林 , 郑启光 . 硅酸铝短纤维强化铝基复合材料的激光切割. 激光技术, 2000, 24(5): 281-284.
[20]	黄开金 , 曾大文 , 谢长生 . 曲率半径和切速对小管径激光切缝宽度的影响. 激光技术, 2000, 24(1): 51-54.

点击查看大图

计量

文章访问数: 4291
HTML全文浏览量: 682
PDF下载量: 729
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

基于热裂法的液晶玻璃基板激光切割技术研究

作者简介: 汪旭煌(1985- ),男,硕士研究生,主要从事激光与物质相互作用方面的研究..

通讯作者: 汪旭煌, laser@zjut.edu.cn ;

Research of the technology of laser cutting LCD glass substrates based on thermal cracking method

Corresponding author: WANG Xu-huang, laser@zjut.edu.cn ;

计量

基于热裂法的液晶玻璃基板激光切割技术研究

通讯作者: 汪旭煌, laser@zjut.edu.cn;

作者简介: 汪旭煌(1985- ),男,硕士研究生,主要从事激光与物质相互作用方面的研究.

English Abstract

Research of the technology of laser cutting LCD glass substrates based on thermal cracking method

Corresponding author: WANG Xu-huang, laser@zjut.edu.cn

全文HTML

目录

留言板

基于热裂法的液晶玻璃基板激光切割技术研究

作者简介: 汪旭煌(1985- ),男,硕士研究生,主要从事激光与物质相互作用方面的研究..

通讯作者: 汪旭煌, laser@zjut.edu.cn ;

Research of the technology of laser cutting LCD glass substrates based on thermal cracking method

Corresponding author: WANG Xu-huang, laser@zjut.edu.cn ;

计量

出版历程

基于热裂法的液晶玻璃基板激光切割技术研究

通讯作者: 汪旭煌, laser@zjut.edu.cn;

作者简介: 汪旭煌(1985- ),男,硕士研究生,主要从事激光与物质相互作用方面的研究.

English Abstract

Research of the technology of laser cutting LCD glass substrates based on thermal cracking method

Corresponding author: WANG Xu-huang, laser@zjut.edu.cn

全文HTML

目录