错边量对车用镀锌钢光纤激光焊接性能的影响

陈根余; 蔡兴; 谭力鹏; 李时春; 张明军

doi:10.3969/j.issn.1001-3806.2012.05.001

错边量对车用镀锌钢光纤激光焊接性能的影响

1.
湖南大学, 汽车车身先进设计制造国家重点实验室, 长沙, 410082;
2.
湖南大学激光研究所, 激光研究所, 长沙, 410082

作者简介: 陈根余(1965- ),男,教授,主要从事汽车激光制造研究及激光微细加工的研究,E-mail:hdgychen@163.com.

基金项目:
国家八六三高技术研究发展计划资助项目(2007AA042006);国家工信部“高档数控机床与基础制造装备”科技重大专项课题资助项目(2009ZX04007-021);国家自然科学基金资助项目(51175165)
中图分类号: TG456.7

Effect of align deviation value on fiber laser welding property of automotive galvanized steel

1.
State Key Laboratory of Advanced Design and Manufacturing for Body, Hunan University, Changsha 410082, China;
2.
Laser Research Institute, Hunan University, Changsha 410082, China
CLC number: TG456.7

摘要: 为了研究错边量变化对车用镀锌钢光纤激光对接焊焊接性能的影响,采用正交试验,获得无错边状态下的最优焊接参量,在该最优参量下进行了不同错边量的焊接接头的表面、截面形貌分析,以及显微硬度、接头力学性能和金相组织测试,还研究了对接间隙对临界错边量的影响。结果表明,当错边量小于或等于0.30mm(约板厚的17%)时,焊缝表面成形良好;焊缝区和热影响区显微硬度高于母材;焊缝拉伸强度优于母材,且拉伸试验均断裂在母材区;错边量的变化对金相组织无明显影响;对接间隙的变化对最大允许错边量值有很大影响。
- 激光技术 /
- 激光焊接 /
- 错边量 /
- 车用镀锌钢 /
- 对接
Abstract: In order to study effect of the align deviation value on welding property of automotive galvanized steel based on fiber laser welding,the orthogonal test was adopted to obtain the best ideal parameters without align deviation.Weld topography and cross section of different align deviation value were analyzed,micro-hardness,mechanical properties and micro-structure of weld were tested,and the effect of different butt joint gaps on the critical align deviation value was analyzed.The results show that when the align deviation value is less or equal to 0.30mm(about 17% of sheet thickness),the weld topography is even and continuous.Micro-hardness in the fusion zone and heat affected zone is higher than that in the base material,the tensile strength of fusion zone is better than that of the base material.The change of the align deviation value does not have much impact on the micro-structure of weld.The butt joint gap has obvious influence on the critical align deviation value.
- laser technique /
- laser welding /
- align deviation value /
- automotive galvanized steel /
- butt joint

[1]	TIAN H B,LIN J P,LIU R T,et al.A review on ultralight auto body and related forming technologies[J].Automotive Engineering,2005, 27(3):381-384(in Chinese).
[2]	WU Q,XU L Y,CHEN G Y,et al.Experimental study about CO2 laser welding of galvanized sheet[J].Laser Technology,2007,31 (6):571-574(in Chinese).
[3]	ZUO T C,WANG X B.Characteristic short technological process of laser manufacturing[J].Chinese Journal of Lasers,2008,35(11):1160-1663(in Chinese).
[4]	WANG J C.Development and expectation of laser welding technology[J].Laser Technology,2001,25(1):48-54(in Chinese).
[5]	CHEN G Y,MEI L F,ZHANG M J,et al.Application and research of laser processing automobile body manufacturing[J].Laser&Optoelectronics Progress,2009(9):17-23(in Chinese).
[6]	XIN L M,ZHAO M Y,XU Z G.Misalignment production and its prediction model in tailored blank laser welding[J].Transactions of the China Welding Institution,2008,29(11):89-92(in Chinese).
[7]	CHEN G Y,WANG Z J,MEI L F,et al.Effect of laser incident angles on welding performance of galvanized sheet for vehicle body[J].Laser Technology,2010,34(6):729-732(in Chinese).
[8]	MA G Y,WU D J,WANG Z H,et al.Weld joint forming of thin hastelloy C-276 sheet of pulsed laser welding[J].Chinese Journal of Lasers,2011,38(6):0603014/1-0603014/5(in Chinese).
[9]	LI Y L,HUANG J,GAO Z G,et al.Structure and properties of high power laser welding of high strength steel B450LAD for vehicles[J].Chinese Journal of Lasers,2008,35(12):2047-2051(in Chinese).
[10]	FANG H S,YANG Z G,YANG J B,et al.Research on bainite transformation in steels[J].Acta Metallurgica Sinica,2005,41 (5):449-457(in Chinese).
[11]	DONG X C,ZHANG X,CHEN Y Q,et al.Weldability of quenched and tempered bainite Q550D heavy plate steel[J].Electric Welding Machine,2010,40(9):58-61(in Chinese).
[12]	LIU Z C,REN H P.Diffusion phase transformation of supercooled austenite[M].Beijing:Science Press,2007:295-306(in Chinese).
[13]	CHEN G Y,CHENG F,ZHANG Y,et al.Effect of butt joint gap to high-strength automobile steel of fiber laser welding[J].Chinese Journal of Lasers,2011,38(6):0603013(in Chinese).

[1]	陈根余 , 吴克如 , 廖生慧 , 邓辉 , 张明军 . V型坡口对钢/铝激光对接熔钎焊性能的影响. 激光技术, 2014, 38(1): 11-16. doi: 10.7510/jgjs.issn.1001-3806.2014.01.003
[2]	唐代明 , 苟淑云 , 王军 . 低合金相变诱发塑性(TRIP)钢激光焊接的研究进展. 激光技术, 2012, 36(2): 145-150,178. doi: 10.3969/j.issn.1001-3806.2012.02.001
[3]	董其峰 , 鄢锉 , 廖先宇 . 激光焊接镀锌钢/冷轧钢异种板材工艺试验研究. 激光技术, 2012, 36(5): 665-669. doi: 10.3969/j.issn.1001-3806.2012.05.023
[4]	陈根余 , 王祖建 , 梅丽芳 , 李时春 . 激光入射角度对车身用镀锌板焊接性能的影响. 激光技术, 2010, 34(6): 729-732. doi: 10.3969/j.issn.1001-3806.2010.06.003
[5]	杨洪亮 , 金湘中 , 修腾飞 , 费鑫江 , 叶颖 . 钢/铝异种金属光纤激光焊接数值模拟. 激光技术, 2016, 40(4): 606-609. doi: 10.7510/jgjs.issn.1001-3806.2016.04.031
[6]	伍强 , 徐兰英 , 陈根余 , 龚金科 , 李力钧 . CO2激光焊接高强度镀锌板的试验研究. 激光技术, 2007, 31(6): 571-574.
[7]	王强 , 焦俊科 , 王飞亚 , 张文武 , 盛立远 . CFRP与不锈钢激光焊接的有限元分析. 激光技术, 2016, 40(6): 853-859. doi: 10.7510/jgjs.issn.1001-3806.2016.06.017
[8]	王玉玲 , 张翔宇 , 胡小红 . 钛合金-不锈钢异种材料激光焊接工艺研究. 激光技术, 2017, 41(6): 816-820. doi: 10.7510/jgjs.issn.1001-3806.2017.06.010
[9]	陈俊科 , 石岩 , 倪聪 , 蒋士春 , 刘佳 . 线能量对奥氏体不锈钢激光焊接质量的影响. 激光技术, 2015, 39(6): 850-853. doi: 10.7510/jgjs.issn.1001-3806.2015.06.025
[10]	方正帅 , 刘佳明 , 黄根哲 , 张宏 , 刘凤德 . 不等厚铝/钢激光焊接接头组织与性能研究. 激光技术, 2023, 47(2): 147-153. doi: 10.7510/jgjs.issn.1001-3806.2023.02.001
[11]	温阳 , 汪苏 , 李晓辉 . 304#不锈钢旋转双焦点激光-TIG焊接组织性能. 激光技术, 2009, 33(6): 593-596. doi: 10.3969/j.issn.1001-3806.2009.06.010
[12]	严军 , 曾晓雁 , 高明 , 邓业平 . 316L不锈钢激光——钨极惰性气体复合焊接工艺研究. 激光技术, 2007, 31(5): 489-492.
[13]	刘海 , 陈辉 . Q345B/304异种钢激光填丝焊接工艺与性能研究. 激光技术, 2024, 48(2): 229-234. doi: 10.7510/jgjs.issn.1001-3806.2024.02.013
[14]	刘西霞 , 黄锐 , 姚刚 , 彭继忠 , 张屹 . 钛合金薄板激光对接焊温度场的数值模拟. 激光技术, 2013, 37(5): 700-704. doi: 10.7510/jgjs.issn.1001-3806.2013.05.030
[15]	周磊磊 . 离焦量对纯钛薄板对接焊缝性能的影响. 激光技术, 2019, 43(3): 397-400. doi: 10.7510/jgjs.issn.1001-3806.2019.03.020
[16]	龚郡 , 魏昕 , 钟世杰 , 汪永超 , 蒙禹舟 . 基于排气通道的车身镀锌板激光叠焊工艺. 激光技术, 2022, 46(1): 94-98. doi: 10.7510/jgjs.issn.1001-3806.2022.01.009
[17]	雷华东 , 徐宾 , 殷俊 . 30CrMnSiA调质钢的激光焊接性研究. 激光技术, 2002, 26(3): 225-228.
[18]	白少俊 , 常保华 , 张骅 , 都东 . 工艺参量对NdFeB永磁体和SPCC钢激光点焊质量的影响. 激光技术, 2010, 34(2): 149-153. doi: 10.3969/j.issn.1001-3806.2010.02.002
[19]	熊建钢 , 胡伦骥 , 刘建华 , 胡席远 , 郭利峰 . 镀锌板激光焊接工艺及锌行为研究. 激光技术, 1998, 22(1): 26-29.
[20]	吴世凯 , 张正伟 , 曹娜 , 江玉军 , 肖荣诗 . 激光焊接用超音速横向气帘喷嘴的研究. 激光技术, 2006, 30(2): 145-147.

点击查看大图

计量

文章访问数: 4063
HTML全文浏览量: 666
PDF下载量: 545
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

留言板

错边量对车用镀锌钢光纤激光焊接性能的影响

作者简介: 陈根余(1965- ),男,教授,主要从事汽车激光制造研究及激光微细加工的研究,E-mail:hdgychen@163.com.

Effect of align deviation value on fiber laser welding property of automotive galvanized steel

计量

错边量对车用镀锌钢光纤激光焊接性能的影响

作者简介: 陈根余(1965- ),男,教授,主要从事汽车激光制造研究及激光微细加工的研究,E-mail:hdgychen@163.com

English Abstract

Effect of align deviation value on fiber laser welding property of automotive galvanized steel

全文HTML

目录

留言板

错边量对车用镀锌钢光纤激光焊接性能的影响

作者简介: 陈根余(1965- ),男,教授,主要从事汽车激光制造研究及激光微细加工的研究,E-mail:hdgychen@163.com.

Effect of align deviation value on fiber laser welding property of automotive galvanized steel

计量

出版历程

错边量对车用镀锌钢光纤激光焊接性能的影响

作者简介: 陈根余(1965- ),男,教授,主要从事汽车激光制造研究及激光微细加工的研究,E-mail:hdgychen@163.com

English Abstract

Effect of align deviation value on fiber laser welding property of automotive galvanized steel

全文HTML

目录